The content down below on the subject of How to Install a Bathtub Yourself is rather fascinating. Don't miss out on it.
Mounting a bath tub isn't exactly rocket science, however it does need strong plumbing, woodworking, and also sometimes, tiling skills. Replacing an old bathtub with a new one is likewise a moderately tough job. If the old bathtub is conveniently available, the job can move speedily; if you need to open a wall to eliminate the old tub as well as position the new tub, the task is much harder. In either case, the project is within a home handyman's skills, although you will require an assistant to leave the old tub and embeded in the brand-new one. Make certain you have actually certified yourself for the task as well as are comfortable attempting it. As opposed to employing a professional to take control of a halfway-completed job, it is much better to consider employing one prior to you begin. Chances are you might require an expert plumber to make tube connections.
This write-up will aid you mount a new tub in your shower room if you have actually currently acquired a new bathtub and do not require to change the setup of your previous water system pipes.
Your devices as well as material list ought to comprise the following:
Preparing for the Installment
First of all, the supporting frame provided with the bath must be fitted (if required) according to the maker's instructions. Next off, fit the taps or mixer to the bath tub. When fitting the faucet block, it is essential to make sure that if the tap comes with a plastic washing machine, it is fitted in between the bath and also the taps. On a plastic bath, it is likewise sensible to fit a sustaining plate under the taps device to prevent stress on the bathtub.
Fit the versatile tap ports to the bottom of the two faucets using 2 nuts and also olives (sometimes supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and after that pass the electrical outlet through the hole in the bathroom. Use the nut supplied by the supplier to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the flexible overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bathroom. Make sure you use all of the provided washing machines.
Connect the trap to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Attach the bottom of the overflow tube in a comparable manner.The bathroom should now be ready to be fitted in its final position.
Removing Old Touches
If you need to change old faucets with new ones as a part of your installation, after that the first thing you need to do is disconnect the supply of water. After doing so, switch on the faucets to drain pipes any type of water staying in the system. The procedure of removing the existing taps can be fairly problematic because of the limited access that is typically the instance.
Use a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that connects the supply pipes to the taps. Have a towel ready for the remaining water that will originate from the pipelines. Once the supply pipes have been removed, utilize the very same device to loosen the nut that holds the taps onto the bath/basin. You will require to quit the solitary taps from transforming throughout this procedure. Once the taps have been eliminated, the holes in the bath/basin will have to be cleaned of any type of old sealing compound.
Before carrying on to fit the brand-new faucets, contrast the pipeline links on the old taps to the new taps. If the old taps are longer than the new taps, after that a shank adapter is needed for the new taps to fit.
Installing the Bathtub
Using the two wooden boards under its feet, put the tub in the called for placement. The wood boards are helpful in evenly spreading the weight of the bath tub over the location of the boards instead of concentrating all the weight onto 4 tiny factors.
The following objective is to make certain that the bathtub is leveled all round. This can be accomplished by inspecting the spirit level and adjusting the feet on the bathtub until the spirit level reads level.
To install faucets, fit all-time low of the furthest versatile tap connector to the ideal supply pipeline by making a compression sign up with; then do the same for the other faucet.
Activate the water system as well as inspect all joints as well as new pipework for leaks and tighten them if necessary. Load the bath tub as well as likewise inspect the overflow outlet and also the regular electrical outlet for leaks.
Ultimately, deal with the bathroom paneling as explained in the producer's instruction manual. Tiling and also securing around the tub ought to wait until the bath tub has been used at least when as this will settle it right into its last setting.
Fitting New Taps
If the tails of the new faucets are plastic, then you will certainly need a plastic connector to stop damages to the thread. One end of the connector fits on the plastic tail of the faucet as well as the other end provides a link to the existing supply pipes.
If you require to fit a monobloc, then you will certainly call for minimizing couplers, which links the 10mm pipeline of the monobloc to the common 15mm supply pipe.
Next, place the tap in the placing hole in the bath/basin ensuring that the washers remain in location between the faucet and the sink. Safeguard the tap in position with the maker offered backnut. As soon as the tap is securely in position, the supply pipes can be linked to the tails of the taps. The taps can either be attached by using corrugated copper piping or with regular tap adapters. The former kind must be connected to the tap finishes first, tightening just by hand. The supply pipes can later on be linked to the various other end. Tighten both ends with a spanner after both ends have actually been connected.
Tiling Around the Tub
In the area where the bathroom meets the ceramic tile, it is necessary to secure the joins with a silicone rubber caulking. This is necessary as the fitting can move sufficient to break an inflexible seal, creating the water to pass through the wall between the bath as well as the tiling, bring about problems with moisture and also possible leaks to the ceiling listed below.
You can choose from a range of coloured sealers to blend in your fixtures as well as fittings. They are offered in tubes and also cartridges, and are capable of securing gaps approximately a size of 3mm (1/8 inch). If you have a larger gap to fill up, you can load it with twists of drenched paper or soft rope. Keep in mind to constantly fill the bathtub with water prior to sealing, to enable the motion experienced when the bathtub is in use. The sealer can fracture fairly early if you do not take into account this movement prior to securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are additionally easily offered on the market. It is advisable to fit the ceramic tiles utilizing water-resistant or water resistant sticky as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Hopefully you enjoyed our post about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround. Thanks for taking a few minutes to browse our piece of content. Are you aware of somebody who is sincerely interested in A Step-by-Step Guide to Installing a Bathtub? Please feel free to share it. Thanks for your time. Visit us again soon.
Book Services